×

Loading...
Ad by
  • 最优利率和cashback可以申请特批，好信用好收入offer更好。请点链接扫码加微信咨询，Scotiabank -- Nick Zhang 6478812600。
Ad by
  • 最优利率和cashback可以申请特批，好信用好收入offer更好。请点链接扫码加微信咨询，Scotiabank -- Nick Zhang 6478812600。

@Manitoba

如果你从alarm公司拿不到installer code （99%拿不到），只能reset / initial你的系统，然后再从新setup包括你所有的zone。reset方法见内。很麻烦的，不建议你独自做。

prostar_100(乌龟怕铁锤)
本文发表在 rolia.net 枫下论坛Most DSC panels can be defaulted by one of the following procedures:


Older systems (boards with EEPROM RESET pins):

1. Remove all power, AC and battery, from the panel.
2. Short the pins on the panel labeled EEPROM RESET.
3. While maintaining the short, power-up the panel and wait for at least 10 seconds before removing the short.
4. Upon removal of the short, the keypad buzzer will beep and the panel will be reset to the factory default values.

Note: If a series of 10 clicks are heard from a relay on the printed circuit board when applying power, it indicates that the board is locked and cannot be defaulted. The system should be replaced.


Newer systems (boards with no EEPROM RESET pins):

1. Remove all power, AC and battery, from the panel.
2. Remove all wires from the Zone 1 and PGM1 terminals.
3. With a piece of wire short the Zone 1 terminal to the PGM1 terminal.
4. Apply AC power to the main panel.
5. When Zone Light 1 is lit on the keypad the default is complete.
6. Remove AC power from the control
7. Remove the wire from the Zone 1 terminal and the PGM1 terminal.
7. Reconnect all original wiring and power up the control.

Note: If a series of 10 clicks are heard from a relay on the printed circuit board when applying power, it indicates that the board is locked and cannot be defaulted. The system should be replaced.


Again, IF the board defaults, it will need reprogrammed for your particular needs. You cannot reprogram the system unless you spend the requisite time with the manuals.更多精彩文章及讨论，请光临枫下论坛 rolia.net
(#4571234@0)
Last Updated: 2008-7-22
This post has been archived. It cannot be replied.
Report

Replies, comments and Discussions:

  • 枫下家园 / 美丽家居 / 怕铁锤的巴西龟请进，讨教报警系统：我的5010当按×8－5010就是一声长嘀，现在还有service，若是unlock的话，什么会丢失？是不是就是拨号的目的号码而已？ -akoei(停车**枫林晚); 2008-7-21 (#4570072@0)
    • di 一长音表示系统block 你的进入, 密码不对. 当初installer 把default 的code给改了。你进不去系统，什么也没更改。你现在还有contract在身，alarm公司不会允许你作任何个人目的改动。 -prostar_100(乌龟怕铁锤); 2008-7-21 (#4570327@0)
      • 如果取消合同,自己怎么该拨出号码呀?比如拨到自己手机上? -net(net); 2008-7-21 (#4570932@0)
        • 如果你从alarm公司拿不到installer code （99%拿不到），只能reset / initial你的系统，然后再从新setup包括你所有的zone。reset方法见内。很麻烦的，不建议你独自做。 -prostar_100(乌龟怕铁锤); 2008-7-22 {1553} (#4571234@0)
          本文发表在 rolia.net 枫下论坛Most DSC panels can be defaulted by one of the following procedures:


          Older systems (boards with EEPROM RESET pins):

          1. Remove all power, AC and battery, from the panel.
          2. Short the pins on the panel labeled EEPROM RESET.
          3. While maintaining the short, power-up the panel and wait for at least 10 seconds before removing the short.
          4. Upon removal of the short, the keypad buzzer will beep and the panel will be reset to the factory default values.

          Note: If a series of 10 clicks are heard from a relay on the printed circuit board when applying power, it indicates that the board is locked and cannot be defaulted. The system should be replaced.


          Newer systems (boards with no EEPROM RESET pins):

          1. Remove all power, AC and battery, from the panel.
          2. Remove all wires from the Zone 1 and PGM1 terminals.
          3. With a piece of wire short the Zone 1 terminal to the PGM1 terminal.
          4. Apply AC power to the main panel.
          5. When Zone Light 1 is lit on the keypad the default is complete.
          6. Remove AC power from the control
          7. Remove the wire from the Zone 1 terminal and the PGM1 terminal.
          7. Reconnect all original wiring and power up the control.

          Note: If a series of 10 clicks are heard from a relay on the printed circuit board when applying power, it indicates that the board is locked and cannot be defaulted. The system should be replaced.


          Again, IF the board defaults, it will need reprogrammed for your particular needs. You cannot reprogram the system unless you spend the requisite time with the manuals.更多精彩文章及讨论，请光临枫下论坛 rolia.net
          • 收藏。等合同到了在问你 -akoei(停车**枫林晚); 2008-7-22 (#4571834@0)

More Topics

  • Keeprite暖气炉不工作了。暖炉有个小玻璃窗的工作状态灯也灭了。 还有救吗？谢指导。
  • 请问：CO警报器是否10年到期必须换？谢谢。
  • 给评价一下这款钻怎么样？打4折呢。没有异议就要下手了。
  • 肉脸强大，来这里请教garage door safety sensor问题。
  • 建房施工，这三招可以预防地下室氡气
    • 枫下论坛主坛 /  枫下家园 /  美丽家居