This topic has been archived. It cannot be replied.
-
枫下家园 / 电脑用户 / 在线求助:打印机打印质量很差,怎么修正?
-cafarmer(农民--渴望杀生);
2003-5-25
(#1205209@0)
-
buy new one, so cheap
-debug(除虫);
2003-5-25
(#1205224@0)
-
买来有点时间了,但用的很少。之前以为墨盒干了,刚买一新的,还是不行。捣鼓半天,从一点墨迹没有,到可以看到点很模糊的图像。我真没啥辄了。
-cafarmer(农民--渴望杀生);
2003-5-25
(#1205241@0)
-
去打印机的属性的地方找找,应该有清洗墨头还有重新排列针数的选项。浪费了n多墨以后,打印机就可以正常工作了。:)
-sweetsmile(巧笑嫣然);
2003-5-25
(#1205271@0)
-
谢谢!//已经如此这般地折腾好几个来回了,效果不大。还耗时3小时,对系统进行了全面升级,也不行。:((
-cafarmer(农民--渴望杀生);
2003-5-25
(#1205300@0)
-
喷墨的就这德性,你得隔三岔五的用它,否则就完蛋。试试用热毛巾捂捂喷头吧,或许行。我的那台BJC-2100折腾了一天也没救活,一气之下,被我扔垃圾桶去了。要是想一劳永逸的话,换个激光的吧。(现在便宜的大概250左右,就是没法打彩色了。)
-dibert(呆伯);
2003-5-25
{79}
(#1205327@0)
-
谢谢!今天就是用水洗过后才有点墨迹的。
-cafarmer(农民--渴望杀生);
2003-5-25
(#1205349@0)
-
几个来回小意思, 我刚从国内呆了4个月回来,换了个墨盒还清洗墨头将近2小时才搞定, 明显跟系统无关嘛, 专心清洗墨头吧
-eooo(千);
2003-5-25
(#1205372@0)
-
怎么清洗的?谢谢!
-cafarmer(农民--渴望杀生);
2003-5-25
(#1205412@0)
-
其实是在用四十刀一个的墨盒狂喷狂喷,一般用两个左右就够买一个新打印机了。
-workopolis(﹡ 枫树下の守望者 ﹡);
2003-5-25
(#1205428@0)
-
我当时是用个旧的,灌了蒸馏水,然后清洗,等头好了,再换上墨盒,如果能温水泡泡喷头就更好了
-elsa(青虫每天爬呀爬);
2003-5-26
(#1205484@0)
-
用热水又冲又泡,效果还是不好。谢谢你!
-cafarmer(农民--渴望杀生);
2003-5-26
(#1205492@0)
-
呵呵,耐心点,我当时也是放了很久后,喷掉了2盒墨盒的水,恢复正常,多泡泡,再试试,还不行的话,就真报废了
-elsa(青虫每天爬呀爬);
2003-5-26
(#1205497@0)
-
其实用高设置来试,打印的东西很早就能看清楚。不过有了从无到有的经历,就想一次彻底搞好。谢谢!//因为用打印机的机会非常少,淘汰的话真有点可惜。
-cafarmer(农民--渴望杀生);
2003-5-26
(#1205501@0)
-
简单,找EGG。
-susse(绝对不鲜);
2003-5-25
(#1205419@0)
-
那个名人?能不能私下透露透露那小技巧?
-cafarmer(农民--渴望杀生);
2003-5-25
(#1205424@0)
-
中介费先。:-D
-susse(绝对不鲜);
2003-5-25
(#1205441@0)
-
下次见面,当面奉呈!
-cafarmer(农民--渴望杀生);
2003-5-25
(#1205445@0)
-
小心不良中介!:P egg是修激光打印机的,喷墨的可能不行吧?
-pingle(窗前花下);
2003-5-26
(#1205453@0)
-
借用蛋泥式东方不败语气:激光打印机都能修,还用说喷墨吗?
-susse(绝对不鲜);
2003-5-26
(#1205464@0)
-
GOOD POINT!
-cafarmer(农民--渴望杀生);
2003-5-26
(#1205466@0)