This topic has been archived. It cannot be replied.
-
枫下家园 / 爱车一族 / 请问HAPPY_LIFE:我在换了O2传感器后发现怠速有起伏的迹象,因无转速表只能靠听,所以不太肯定,您的也是这样吗?还有您说您换前加速有类似滞后的一跳一跳的感觉,换后似乎好了,可为什么我的相反呢?未换前(因检查方法有误,不知好坏,可能是冤案)怠速和加速均正常,换后反而有时会加不速呢?
-elantra93(拆家);
2002-6-23
{86}
(#595354@0)
-
我的车现在一切正常,耗油也不高,一个星期将近400公里,20块油钱。原来现象是雨天有时踩下油门车不动,要踩的很深才行。不过我当时换传感器的时候顺便把air temp sensor也换了(一辆旧车上弄的)。换air temp sensor的原因是当时浆液dx说了句,于是就顺便换了它。
-happy_life(happy_life);
2002-6-24
{61}
(#597952@0)
-
我就是不明白为什么您的怠速能稳定?我昨天又查了O2的输出电压,怠速是确实是在0。3至0。7之间波动,同时怠速的声音也相应地高低起伏;猛踩油门瞬间就高到0。8V,但马上就落回近0V,这说明油气比的控制至少是工作的(不一定是对的),同时也解释了为什么有时踩下油门觉得加速乏力。
怠速是由ISC控制进气量,油气比是根据O2的值是否大於还是小於0。45V控制油的注入量,踩油门相当于油过多,必然引起O2的反应以减少油注入量,这两个控制的效果是相反的。
-elantra93(拆家);
2002-6-27
{384}
(#603417@0)
-
加速的时候O2 sensor 的电压应该立刻增加到 0.9左右,0.8 还是有些低。另外立刻回到 0 伏左右是不正常的。O2 sensor 似乎还是有问题。怠速时测测10 秒之内 voltage cross 450mv 的次数,至少10 次以上才是正常的。
-violent_panda(暴力大熊猫);
2002-6-27
(#603460@0)
-
差不多是1秒经过0。45V(这个值只能说是平均值)一次,至於能不能到0。9V就看O2得了,我还能怎么样呢?我正想找理由退了O2,因为我花了近100块,本指望通过节省油费15%,(我每月油费约150块),在1年内收回这笔投资,但现在看开埠仅毫无意义,反而有时加速无力。
-elantra93(拆家);
2002-6-27
{146}
(#603475@0)
-
如果是平均 1 秒 cross 0.45V 一次,这个 sensor 不太好。好的 sensor 在10 秒内可以变化 20 次以上,越敏感当然对油门的反应越快了。
-violent_panda(暴力大熊猫);
2002-6-27
(#603822@0)
-
是“博氏”的,您认为可以此为由退换吗?我很费了点时间才把信号引出来,估计权威的方法是存储示波器的打印件。
-elantra93(拆家);
2002-6-27
(#603835@0)
-
牌子不错。最少变化8 次是可以接受的。你说你的volmeter 不好,如果用低阻抗的表会损坏 sensor. 还可能 fuel pump工作不好,throttle 气门开关不灵,或者fuel injector 太脏。怠速的时候仔细听能有细小频率很快的咯哒咯嗒的声音,那是 fuel injector 的声音。如果声音断断续续就是太脏了。如果你听过 fuel injector 喷油的声音就可以很容易在发动机的噪声里捕捉到那个声音。
-violent_panda(暴力大熊猫);
2002-6-27
{142}
(#603893@0)
-
找根短细软线,插在插座内后再把原o2的插头很勉强地插一半儿进去,多了挤坏了,少了接触不良;这时是标准的带加热器的原状态,读数在20K(1V挡)与100K(5V档)负载区别不大,数字化的表稳定显示没那么快,数字表1秒完成测量还凑付,半秒我不太肯定。
-elantra93(拆家);
2002-6-27
{114}
(#603914@0)
-
确切地说这个次数是这个油气比控制系统闭环时的时间常数过大,不一定是O2不好。
-elantra93(拆家);
2002-6-27
(#603853@0)
-
对。有可能。所以我在上面的贴子里怀疑是 fuel system 的问题。做 flush 先。不过自己做 fuel flush 有些麻烦,需要 air pump 加压。
-violent_panda(暴力大熊猫);
2002-6-27
(#603904@0)
-
按下葫芦浮起瓢,我看我的车几乎没有一处是好的,我现在花在上面的钱已超过税前价的一半。
-elantra93(拆家);
2002-6-27
(#603933@0)
-
呵呵,我也有这个趋势了。老车做 fuel flush 挺有用的。外面做要五六十块。其实我觉得这样挺好,通过买旧车学习新知识。我的车现在几乎纯粹拿来练手用了。反正很破,弄坏了也不太心疼,弄好了还很高兴 :D
-violent_panda(暴力大熊猫);
2002-6-27
(#603949@0)
-
你还想练点简单的吗?明天俺要换机油,冲洗冷却系统...
-mildkiller(M.K.);
2002-6-27
(#603996@0)
-
如果可以不见面,帮你做这个没问题。明天我还要上班啊。:D
-violent_panda(暴力大熊猫);
2002-6-27
(#604018@0)
-
你可以象俺那个阿拉伯邻居MM,蒙个面纱,只露俩大眼睛叽里咕噜乱转,所有表情都在里面,搞的俺特想一把揪下她的面纱看看长啥样?
-mildkiller(M.K.);
2002-6-27
(#604034@0)
-
哈哈,如果你把她的棉纱弄掉了,恐怕就必须娶她为妻了吧?
-violent_panda(暴力大熊猫);
2002-6-27
(#604048@0)
-
Haha, Same feeling. It is a experiment.
-happy_life(happy_life);
2002-6-27
(#604038@0)
-
^_^
-violent_panda(暴力大熊猫);
2002-6-27
(#604056@0)
-
Hi, everyone:
Anyone could show me how to replace the OS2? I was charge CDN$370 for the scanning , replacement and part. Thanks a lot.
-michael_michael(淡泊宁静);
2002-6-27
(#603847@0)
-
只要您能当街旁若无人地反身贴地地钻到车头下面,手上有把22mm的扳手,带好手套,拆装都不难。我的问题是装上新的不仅毫无改善,反而有新的问题。
-elantra93(拆家);
2002-6-27
(#603870@0)
-
先弄清 o2 sensor 的位置。买一把 7/8 inch 的扳手(或者专门用于o2 sensor 的套筒),买个新的sensor(最好在买些 anti-seize)。在老sensor 上多喷penetrating oil, 放一个晚上。然后replace it. 一般要从车下拆卸。
-violent_panda(暴力大熊猫);
2002-6-27
(#603918@0)
-
Where is OS2? My car is 96 Taurus GL. After scanning, the dealer told me #1 sparker also is not good. They replaced it incidently. If you find your car incompetent, take into account the sparker.
-michael_michael(淡泊宁静);
2002-6-27
(#604132@0)
-
ECU doesn't interpret O2 signal so quickly(otherwise every car would be like dancing). Step down the gas pedal suddenly will cause O2 vultage rising because there are not enough air.After one cycle, the huge volume air will be draw in and then the O2 vultage will drop down.
Idle is not stable usually caused by the unbalance force of burning.
I believe that's because the inside burning in your car's chamber is not perfect. Then the O2 sensor can't reach the right ratio.(Even the 0.4V is a false one because real ratio will be larger than 14.7).
-happy_life(happy_life);
2002-6-27
{376}
(#603911@0)
-
我的运气不如您好,还不如500块换个儿发动机算了。
-elantra93(拆家);
2002-6-27
(#603944@0)
-
Notice the compression ratio and the fuel injector's quality. That's the source of burning problem.
-happy_life(happy_life);
2002-6-27
(#603962@0)
-
94%.
-elantra93(拆家);
2002-6-27
(#603977@0)
-
If these two have problem, usually you are difficult to start the engine especially in cold day. (when you start engine >3 secs that means hard to start).So when you buy a car, better choose a cold day and check start status very carefully.
-happy_life(happy_life);
2002-6-27
{86}
(#603985@0)
-
俺的车据说FUEL PUMP有点弱,经常第一次不能点火,喘口气就好了.俺想练手都不知从哪下手~~
-mildkiller(M.K.);
2002-6-27
(#604009@0)
-
You can check it by set key in "ON" for 3 secs first(not "START" position). Then try to start the car. If it is ok , then is the fuel pump. But if it still have problem, hehe.. you better have to begin worry...
-happy_life(happy_life);
2002-6-27
(#604059@0)
-
不是油泵,就是发动机完蛋了?5555~~~上次FORD DEALER告诉俺油泵有点上年纪了,但是按照手册上参数,还算在正常范围内,所以俺没有理会.
-mildkiller(M.K.);
2002-6-27
(#604100@0)
-
No. hehe.. I just frighten you.....Don't jump to the conclusion. You can try it first. It should be ok. Good luck.
-happy_life(happy_life);
2002-6-27
(#604113@0)
-
把耳朵贴在车身上,然后把钥匙转到 "ON" (不要 start),立刻应该听到清晰而连续的 “兹~~~”的声音,持续大约几秒种。那是 fuel pump 供一些油供启动用。如果没有这个声音,嘿嘿,fuel pump 完蛋了。
-violent_panda(暴力大熊猫);
2002-6-27
(#604082@0)
-
我准备投入46块换4个“铱”火花塞以确保点火系没问题,否则点火困难也可能是电气系问题。
-elantra93(拆家);
2002-6-27
(#604040@0)
-
火花塞其实挺耐用的。我接触过的几辆老爷车点火困难都不是因为火花塞。distributor 和线路的问题最多。还有就是油泵和 coolant sensor.
-violent_panda(暴力大熊猫);
2002-6-27
(#604074@0)
-
到底是不是油泵问题可以再投资40-50块买个油路压力表再测一遍,就是换一套“铱”合金的火花塞也不过是我每月油钱的三分之一,只要能把油耗由15L降到10L,一个月就收回成本。
-elantra93(拆家);
2002-6-27
(#604469@0)
-
我是真的不认为换铱合金火花塞能有那么大的功效。不过还是希望能达到你想要的结果。等你的好消息。:D
-violent_panda(暴力大熊猫);
2002-6-27
(#604514@0)
-
No,no, do need waste money in here. You can check the resistor of wire set(that's the fragile part for elantra). Anyway, I replace with the normal spark plugs, there is no problem at all.
-happy_life(happy_life);
2002-6-27
(#604080@0)
-
//hands
-violent_panda(暴力大熊猫);
2002-6-27
(#604087@0)
-
线全部测过,阻值无问题,只是第4号线似乎有点接触不良,已换。我反而觉得火花塞很正要,不信您可比较一下,我现在的是5000公里前换NGK的G沟式,现在是目测间隙增大,表面有氧化灼烧感,且略有油迹。
-elantra93(拆家);
2002-6-27
(#604453@0)
-
Please let me know the result. If it is useful, maybe I need change it too. hehe.. You are the first one to eat the crab. Good luck!
-happy_life(happy_life);
2002-6-27
(#604502@0)